After extensive research that included vintage documentation, consultations with experts, and analysis of multiple original Uni-Vibe units from 1968 to 1974, Sabbadius Electronics discovered several component differences among those units\u2014ranging from capacitors and resistors to light bulbs and photoresistors (LDRs). These subtle variations helped shape the iconic sound of different versions.
\nAs a result, SABBADIUS now offers 3 meticulously crafted versions of the Funky-Vibe ST:
\nVERSIONS AVAILABLE SABBADIUS 1968 Funky-Vibe ST: Based on the original 1968 Honey UNICORD Uni-Vibe, this version is the most popular and widely associated with Jimi Hendrix. It offers a higher maximum speed than later models, delivering a deeper, more responsive modulation effect.
\nSABBADIUS 1969 Funky-Vibe ST: Modeled after the 1969 Shin-ei Companion version, which took over production after Honey UNICORD went bankrupt. While retaining the Uni-Vibe’s essence, it includes internal component changes that give it a slightly different tonal character, reminiscent of tones used by David Gilmour, Robin Trower, and late-period Hendrix.
\nSABBADIUS FILLMORE EAST Funky-Vibe ST: According to some Uni-Vibe experts, this Uni-Vibe version is possibly the one Jimi Hendrix used in 1969 and 1970, whereas others said that Jimi used a 1968 Uni-Vibe in the United States and a 1969 version in Europe. The thing is that if you pay attention to the sound from the same song played in the U.S.A and compare it to the one played in Europe, including England, you will notice that the Throb of the Vibe and the effect\u2019s \u00abwave sound\u00bb do not evoke the same \u00abChewy\u00bb sound we might find in Jimi\u2019s performances. Now I found that the SABBADIUS FILLMORE EAST Funky-Vibe version captures that \u201cCHEWY\u201d SOUND similar to the 69 & 70 Uni-Vibe version.
\nTECHNICAL SPECIFICATIONS:
\n\u00b7 – Transistors: Matsushita 2SC828 for the signal path and 2SC539-type for the preamp stage, as in the original Uni-Vibe.
\n– Custom-made 7 mm LDRs (CdS cells) built exclusively for SABBADIUS Electronics.
\n– 100% hand-wired and hand-soldered circuitry
\n– Fully analog circuit
\n– NEW: The current PCB layout now matches the physical size of the original Uni-Vibe circuit from the late ’60s and early ’70s. After building and comparing more compact versions up to serial number #1999\u2014which used the exact same circuit but in a smaller PCB footprint\u2014we discovered that the larger, original-style layout imparts a unique tonal \u201cmojo\u201d to the sound. This subtle but noticeable sonic enhancement has been validated through direct comparison with an original Uni-Vibe unit owned by SABBADIUS.
\nCONTROLS AND FUNCTIONS:
\n\u00b7 VOLUME: Sets the overall output level.
\n\u00b7 SPEED: Adjusts the modulation rate.
\n\u00b7 INTENSITY: Controls the depth of the modulation.
\n\u00b7 CHORUS\/VIBRATO Rocker Switch:
\no RED DOWN: CHORUS Mode
\no WHITE DOWN: VIBRATO Mode
\n\u00b7 CANCEL Footswitch: Deactivates the internal lamp and disables the modulation effect, allowing the unit to act as a high-impedance preamp\u2014just like the original Uni-Vibe when its foot controller’s tact switch was used.
\n\u00b7 TRUE BYPASS Footswitch: Premium 3PDT switch for bypassing the effect.
\n\u00b7 LED Indicator: Pulses in sync with the internal lamp, showing the modulation speed.
\n\u00b7 POWER SWITCH ON\/OFF: Turns the unit on or off.
\n\u00b7 Fuse Socket: Protects the circuit from voltage surges. Includes an internal fuse and an extra spare.
\n\u00b7 EXPRESSION PEDAL JACK (6.5 mm \/ 1\/4\u201d Amphenol): Allows real-time control of modulation speed.
\nIMPORTANT: Only use a specially built expression pedal. A detailed SHEET MANUAL is included (EXPRESSION PEDAL NOT INCLUDED).
\nCONNECTIONS
\n\u00b7 INSTRUMENT IN: 1\/4\u201d (6.5 mm) Neutrik input jack for instruments.
\n\u00b7 OUTPUT: 1\/4\u201d (6.5 mm) Neutrik output jack to amp or other effects.
\n\u00b7 EXP PEDAL: Amphenol 1\/4\u201d jack for dedicated expression pedal.
\n\u00b7 POWER INPUT: 18V DC \/ 200mA, center-negative. Use a high-quality regulated power supply.
\nENCLOSURE AND BUILD
\n\u00b7 Enclosure: Aluminum housing with stainless steel base.
\n\u00b7 Finish: Powder Coating Paint.
\n\u00b7 Dimensions: 180 mm (L) x 130 mm (W) x 78 mm (H)
\n\u00b7 Weight: Approximately 800 grams
\nINCLUDED IN THE BOX
\n\u00b7 Funky-Vibe ST (Standard)
\n\u00b7 User Manual with Detailed Expression Pedal Guide.
\n\u00b7 Spare Fuse
\nSpare 2sC828 Backup Transistors for the LFO (Can be easy replaced in the transistors sockets if the LFO transistors were in short cut.<\/p>\n","protected":false},"excerpt":{"rendered":"
After extensive research that included vintage documentation, consultations with experts, and analysis of multiple original Uni-Vibe units from 1968 to<\/p>\n